Set of leads for batter charging. Ring terminals for battery, 2 pin connector for charger to plug into. Often required if you charge more than one bike using your Motobatt Smart Charger

 2 in stock

Mesh silencer gasket, silencer bush or muffler gasket shim for exhaust joint between silencer and downpipe

2 exhaust bushes required per bike

 2 in stock

2B007137

Universal hydraulic brake light switch. This hydraulic switch replaces discontinued brakelight switches by bolting in place of a single banjo bolt on the handlebar or rear brake master cylinder

NB stop light switch may be supplied with or without 2 pin block connector. Can be used in place of Guzzi ref. 32657060

 1 in stock

Brembo pad pin kit for Brembo P4 30/34F calipers fitted to front forks, two pins

Brembo ref. 120394230

 1 in stock

 01659130 GU01659130 01 65 91 30
 0165 9130 0165.9130 01.65.91.30

Domino left hand switchgear with lights on - park - off, high and low beam, pass, indicator and horn switches. Same style switch as ELA01738.

Already wired in to 9 pin block connector (you may need to alter the wiring on your bike to correspond to this block connector). Originally fitted as standard to early V11 Sport models. See the wiring diagram on our technical documents page for help installing this switchgear. See Greg Bender's website for a custom sub-loom that enables easy fitting of this part to models previously fitted with LEGO style swithgear

 1 in stock

 01738030 GU01738030 01 73 80 30
 0173 8030 0173.8030 01.73.80.30

Right hand Domino type starter switch for use with separate throttle, e.g. Tommaselli twin pull throttles ACA10500 or ACA10501

On most bikes this will not plug directly into the wiring loom, you will need to match the wires to your loom. If replacing 'Lego' type switchgear (e.g. Le Mans 2, V50) with integrated twistgrip you will need a separate twistgrip, see ACA10500 and ACA10501. Packaging may include explanation of switchgear wire covers. This type originally fitted as standard to the early V11 Sport models. See the wiring diagram on our technical documents page for help installing this switchgear.. Molex connectors available separately.

 1 in stock

 01738800 GU01738800 01 73 88 00
 0173 8800 0173.8800 01.73.88.00

Pad pin kit fitted to rear, double pin.

Incorrectly listed in Guzzi parts books as 31659181 for the V7 II, V7 III , V7 850 and V85TT. This two pin kit is the correct part for the rear caliper on these models.

 1 in stock

AP8133799

Also fits Aprilia Mana 850

Oil pump nut on some small twins- check parts book for exact application

 1 in stock

 92602510 GU92602510 92 60 25 10
 9260 2510 9260.2510 92.60.25.10

Spring, used as rocker thust spring valve gear on older big twin models

 1 in stock

 94322215 GU94322215 94 32 22 15
 9432 2215 9432.2215 94.32.22.15

The SW-Motech mirror extender kit contains a pair of black mirror extensions that allow you to move your existing mirrors out and up by up to 4cm.

To ensure that your own shoulders aren't the only thing you see in the rear-view mirror, the extensions provide a significantly improved field of vision by relocating the mirrors to the outside. Once adjusted and screwed on, the sturdy, well-designed extensions provide secure hold for the mirrors, even when riding off-road or at high speeds.

See this link for fitting instructions.

 1 in stock